TLMscopeDeutsch

Frequently asked questions

Short answers about opening Spektrum telemetry logs and reading them in TLMscope. Each answer points to the page with the details.

Updated

Frequently asked questions

What is TLMscope? #

TLMscope is a free, browser-based viewer and analyzer for Spektrum .TLM telemetry logs. It runs on Windows, macOS, Linux, Android and iOS without installing anything, and the files stay on your device.

From a log it shows:

  • a plain-language summary of each flight
  • charts of height, climb, motor, battery and radio link
  • a GPS map with 3D replay
  • thermals
  • flight modes and stabilization
  • battery ageing across flights
  • the total flight time per model and a CSV export of the session list

What is a Spektrum .TLM file? #

A .TLM file is the telemetry log a Spektrum transmitter saves while you fly. It holds what the receiver and the sensors in the model reported, for example signal strength, battery voltage, motor current, height and GPS position. See How to open Spektrum .TLM files.

How do I open a .TLM file? #

  1. Copy the .TLM file from your transmitter to your computer or phone.
  2. Drop it onto the start page, or click to choose it.
  3. TLMscope reads it in your browser and shows a summary of each flight.

No log at hand? Load the demo flight. The step-by-step guide shows where the files are on NX, iX and DX transmitters.

Where does a Spektrum NX store its telemetry logs? #

On its internal storage:

  • logs named after the model, as .TLM files
  • automatic logs for each session, in the AutoLog folder

Connect the transmitter by USB and choose the option to access the internal storage to copy them.

Is there a Spektrum TLM viewer for Mac, Linux or phones? #

Yes. TLMscope is a web page, so it runs in a current browser on Windows, macOS, Linux, Android and iOS. Nothing needs to be installed. The map and the 3D replay use WebGL, which current browsers support.

Are my flight logs uploaded anywhere? #

No. Files are read in your browser and never leave your device.

Only for logs with GPS, the map loads map images from OpenFreeMap, which therefore sees roughly where you flew. The same goes for the elevation data of the relief view (beta) from Amazon Web Services, loaded only when you switch it on. A CSV export is made in your browser and saved on your device. See the privacy notice.

Does TLMscope work without internet? #

Yes, after one visit with internet:

  1. Open TLMscope once with internet.
  2. Wait until the footer says Works offline.
  3. From then on it also opens without a connection, for example at the flying field.

On iPhone and iPad, add TLMscope to the home screen so Safari keeps it. Only the map in the Flight path tab needs internet.

How do I install TLMscope on my phone or laptop? #

TLMscope runs in the browser, so there is nothing to download from an app store. You can still add it like an app:

  • Android (Chrome): open TLMscope, tap the menu ⋮ and choose Install app or Add to Home screen.
  • iPhone and iPad (Safari): tap Share, then Add to Home Screen. This also keeps the offline copy, which Safari otherwise deletes after some days without use.
  • Laptop with Chrome or Edge: click the install icon at the right end of the address bar.
  • Mac with Safari: choose File → Add to Dock.
  • Firefox: a bookmark is enough.

Then open TLMscope once with internet and wait until the footer says Works offline. After that it also opens without a connection; only the map needs internet.

Your log files are never uploaded or stored.

How can I send feedback or a log? #

Use the Feedback button at the top of TLMscope, or the small links under the ratings, at the end of each tab and on the start page:

  1. Open the feedback dialog and check the technical details that would be sent. You can switch them off.
  2. Choose Continue to the form, pick the kind of message and write it down.
  3. Add your email address only if you want an answer.

The form is provided by Tally (Belgium) and loads only after you continue. Log files, file names, model names, positions and flight values are never sent. If I need a log, I ask you in my reply, and you can send it by email. Logs with GPS show where you fly, so only share what you are comfortable with.

Which transmitters and sensors does it support? #

Logs from Spektrum NX and iX transmitters are tested. DX logs should work but are not tested yet. Radio link, motor, battery, height, GPS and more show up depending on the sensors your model carries. See Supported transmitters and sensors.

How many frame losses are normal on a Spektrum receiver? #

  • Normal: Spektrum receiver manuals describe up to about 100 per minute in the air as normal.
  • High quality: TLMscope rates up to about 20 per minute as high quality.
  • Holds, half a second or longer without signal, should not happen.

More in Understand your Spektrum telemetry.

What is a hold in Spektrum telemetry? #

A hold is half a second or longer without any signal at the receiver: 45 frames in a row that no receiver got. The receiver then applies its hold or failsafe setting. TLMscope always rates a hold during flight as critical.

When should I retire a LiPo battery? #

A common rule of thumb is to retire a pack when its internal resistance reaches about 15 mΩ per cell. TLMscope estimates this value from the voltage sag in flight and follows it across flights for Spektrum Smart batteries.

Can TLMscope count my flight hours per model? #

Yes, for the logs you load. Above the session list, TLMscope adds up the time in the air of the loaded flights, for all models or the one you choose. Only time in the air counts: pauses of two minutes or more on the ground between two flights of one session are left out. When some flights have neither a height sensor nor GPS, their time is estimated from the motor and the model's movement, and the total is marked “≈”.

TLMscope stores nothing between visits, so the total covers the files loaded now. To keep a flight log, use Export as CSV, see the next question.

Can I convert a .TLM file to CSV or Excel? #

Partly. Export as CSV above the session list saves one line per session: model, date, start time, type, session and air time, frame losses, holds, lowest receiver voltage, battery ID, charge used and the source file. With German settings it uses a semicolon and a decimal comma, so Excel opens it directly.

There is no export of the raw sensor values. For that, TLM Viewer on Windows exports CSV; see Spektrum TLM viewers compared.

How can I see whether AS3X or SAFE was on during a flight? #

With a receiver with AS3X or SAFE, the log contains the flight mode and which functions were on. The Aircraft tab shows the time in the air per function (AS3X, SAFE, heading hold or no stabilization) and per flight mode, the AS3X gain for roll, pitch and yaw, and the flight modes over time. A gain of 0 means AS3X did not correct at all, for example with the gain knob turned down. More in Understand your Spektrum telemetry.

What is the difference between a hold and a brown-out? #

  • Hold: the radio link was lost for half a second or longer, so the receiver went to its hold or failsafe setting. The receiver voltage stays normal. TLMscope rates it in the radio link.
  • Brown-out: the voltage at the receiver dropped so far that the receiver restarted. That is a power problem, not a radio problem. In the log it shows as a voltage drop and usually a gap or a new session, not as a hold.

Unplugging the battery after landing also makes the voltage fall. TLMscope leaves those moments out, so they do not count as a brown-out.

Why does my log have gaps when the model is far away? #

Telemetry often reaches less far than the control link. Some Spektrum receivers send telemetry only over a short range, about 100 to 150 m. Beyond that the log has gaps or stops changing while the model is still under control. A gap alone is therefore no loss of control. The receiver keeps counting frame losses and holds, so look at them once the telemetry is back.

Can TLMscope show the height without a vario? #

Yes, with a Spektrum GPS sensor. TLMscope then takes the height above the take-off spot from the GPS altitude and shows the highest point and the height profile. GPS height is less exact, about ±5 to 10 m, so climbs, lift and glide still need a vario. Without a vario and without GPS the height stays empty, and the time in the air is estimated from the motor and the model's movement.

Is TLMscope free, and is it made by Spektrum? #

TLMscope is free, needs no account and is an independent hobby project by a model flyer. It is not made or endorsed by Spektrum or Horizon Hobby. How it compares with other viewers is in Spektrum TLM viewers compared.

Is there an alternative to TLM Viewer? #

Yes. The main options:

  • TLM Viewer: a long-standing, open-source Windows program with export to CSV and KML.
  • TLMscope: free, runs in the browser on any device, explains each flight in plain words and exports the session list as CSV.
  • Log Explorer: a paid desktop program that also reads other radio systems.

See Spektrum TLM viewers compared.