Understand your Spektrum telemetry
A telemetry log is full of counters and voltages. This page explains the important ones in plain words, together with the rules of thumb TLMscope uses for its ratings.
Updated
Radio link: frame losses, fades and holds
The receiver counts what goes wrong on the radio link:
- Frame losses are frames that no receiver got. A few are normal. The transmitter sends about 91 frames per second, so 100 per minute is under 2 % of them. TLMscope rates up to about 20 per minute as high quality and up to about 100 per minute in the air as normal, in line with Spektrum receiver manuals. What counts is how fast the counter rises in the air, not its total; on the ground it rises much faster anyway.
- Fades count the frames a single receiver missed. A is the main receiver (with two antennas, both count as one); B, L and R are remote receivers. A is usually the highest, because the main receiver sits deep in the fuselage between cables, battery and controller. Compare the remote receivers with each other: one far above the others is badly placed. With only one receiver, look at the frame losses instead.
- Holds are half a second or longer without any signal (45 frames in a row missed by every receiver). The receiver then goes to its hold or failsafe setting. A hold in flight always rates the radio link as critical and is marked on its timeline.
These counters start at zero when the receiver powers up. TLMscope shows what happened during the session.
Signal strength
The signal strength at the receiver is given in dBm: the closer to zero, the stronger. In TLMscope's own sample flights, frame losses rose sharply below about −80 dBm. It therefore rates −70 dBm or better as high, down to −80 dBm as normal, down to −85 dBm as weak and anything lower as critical.
The Radio link tab plots the signal against height, because height and distance often go together. Under “Over time”, click a level to show only those seconds and step from one to the next.
Receiver voltage
The voltage at the receiver should stay steady under load. TLMscope rates 5.2 V or more as steady, 4.8 V or more as OK, anything above 4.0 V as dips and below that as brown-out risk. Look for dips when several servos move at once. The moments of switching on and off, such as unplugging the battery after landing, are left out, so they do not look like a brown-out. The AR8360T manual asks to stay above 4.8 V under load, and receivers of this family drop out below about 3.5 V.
Battery: charge used, cells and internal resistance
- Charge used is the share of the pack's capacity drawn in the session. TLMscope rates up to 50 % as plenty left, up to 70 % as fine, up to 80 % as land soon and more as over-drawn: the common 80 % rule.
- Cell voltages from a Spektrum Smart battery show the lowest and highest cell. A growing difference between cells points to an unbalanced pack.
- Internal resistance per cell is estimated from how far the voltage sags when the motor draws current, so it includes the wiring. Under 10 mΩ per cell is excellent, up to 12 mΩ acceptable, and above 15 mΩ it is time to retire the pack, a rule of thumb from LiPo guides. The Batteries page follows this value from flight to flight and estimates how many charge cycles are left.
- Temperature of 35 to 45 °C after a flight is normal. TLMscope warns from 45 °C and treats 60 °C as the usual ceiling. Batteries without a temperature sensor send 0; TLMscope then shows no battery temperature.
Motor and speed controller
Smart speed controllers such as the Avian report motor current, input voltage, throttle, rpm and temperatures. TLMscope uses them to find the motor runs, to work out the charge used per minute in the air and the height gained per 100 mAh in motor climbs.
Height, climb rate and thermals
A vario or altimeter sensor reports height and climb rate. TLMscope splits a flight into motor climbs, glides and lift: climbing with the motor off for about ten seconds or longer is marked as lift. The centres of thermals are estimated from circling flight and shown on the map.
Without a vario, a Spektrum GPS sensor gives the height above the take-off spot. It is less exact, about ±5 to 10 m, so TLMscope shows the highest point and the height profile, but no climbs, lift or glide.
Time in the air and total flight time
The time in the air comes from the height, or from the GPS speed, or, without either, from the motor and the model's movement; that last estimate is marked “about”. Pauses of two minutes or more on the ground between two flights of one session do not count. Above the session list, TLMscope adds up the time in the air of the loaded flights, per model when one is chosen, marked “≈” when part of it is estimated.
Loads and rotation
Receivers with AS3X or SAFE report loads in g and rotation rates. TLMscope uses them to detect circling and to tell how gentle, moderate, sporty or hard a flight was.
Stabilization and flight modes
Receivers with AS3X or SAFE also report the flight mode and which functions are on: AS3X, SAFE and heading hold. The Aircraft tab shows the time in the air per function and per flight mode, and the AS3X gain for roll, pitch and yaw. A gain of 0 means AS3X does not correct at all.
Frequently asked questions
How many frame losses are normal on a Spektrum receiver? #
Spektrum receiver manuals describe up to about 100 per minute in the air as normal. TLMscope rates up to about 20 per minute as high quality. Holds, half a second or longer without signal, should not happen.
What is a hold in Spektrum telemetry? #
A hold is half a second or longer without any signal at the receiver: 45 frames in a row that no receiver got. The receiver then applies its hold or failsafe setting. TLMscope always rates a hold during flight as critical.
When should I retire a LiPo battery? #
A common rule of thumb is to retire a pack when its internal resistance reaches about 15 mΩ per cell. TLMscope estimates this value from the voltage sag in flight and follows it across flights for Spektrum Smart batteries.